Xinje DS2-21P5-AS2 DS5L-21P5-AS2 AC servo motor and Driver

Xinje DS2-21P5-AS2 DS5L-21P5-AS2
AC servo motor and Driver in Lahore Pakistan

Here are some visuals of the Xinje DS2‑21P5‑AS2 servo driver, Xinje DS5L‑series servo motor (750 W class), and typical gear reducer box setups for reference.

Product Overview & Specifications

1. Xinje DS2‑21P5‑AS2 (Servo Driver – 1.5 kW)

• Power & Supply: Supports single-phase or three-phase AC 200–240 V, 50/60 Hz. Rated output current is 6.0 A (RMS), with a maximum of 18 A RMS.Elecok

• Control Modes: Offers seamless switching between position, speed, and torque control modes.ElecokXinje Electric

• I/O & Communication:

  • Digital Input: 5 channels

  • Digital Output: 3 channels

  • Supports two types of pulse input, and 24 V open-collector output signaling

  • RS‑232 communication for PC or HMI interfacingElecokXinje Electric

• Protection Features: Built-in regenerative resistor for safe handling of energy during deceleration, plus over-voltage, under-voltage, over-temperature, overload, overspeed, short circuit, and abnormal encoder protection.Xinje ElectricElecok

• Performance: Supports response up to 400 Hz, ideal for high-performance motion applications.Elecok

2. Xinje DS5L (PTA series) – 750 W Class

• Overview: Pulse-type servo driver offering up to 2.6 kW; the DS5L‑21P5‑PTA fits your 750 W requirement.Xinje Electric

• I/O Channels: For ≤ 750 W models, 3 DI and 3 DO; for higher power models, 4 DI and 4 DO.Xinje Electric

• Encoder Feedback: Uses a 17-bit or 23-bit serial communication encoder (PTA).Xinje Electric

• Control & Signals:

  • Compatible with pulse + direction, AB-phase, and CW/CCW input

  • Open collector interface (+24 V)

  • Fast pulse input up to 200 kppsXinje Electric

• Protection & Reliability: Same suite of guard functions—overload, over-voltage, encoder errors, etc.—plus LED display and 4-button interface for parameter setup and status monitoring.Xinje Electric

• Control Modes & Features:

  • Built-in position, speed, and torque control modes with seamless transitions

  • Feedforward compensation up to 100% (1% resolution)

  • Electronic gear ratio support: 1/10000 to 10000, enabling accurate motion correspondence to load output

  • Precise stability: ≤ ±0.01% with full load and output voltage change, ≤ ±0.1% with ambient temp shiftsXinje Electric

How to Use – Step-by-Step Guide

A. Installation & Wiring

1. Power & Motor Connections: Follow polarity and phase guidance—connect motor to U/V/W, power to L1/L2/L3 (for DS2‑21P5‑AS2) or equivalent terminals. Use internal or external regenerative resistor as needed.ManualsLibElecok

2. Grounding: Use at least 2 mm² wire to ground all motor and driver earth terminals.ManualsLib

3. Signal Wiring:

   • For pulse control: DI inputs for PUL, DIR or AB-phase; DO outputs for alarms/status.

   • Connect RS‑232 (COM1) for PC communications; cannot use both RS‑232 and RS‑485 concurrently.ManualsLib+1

B. Parameter Setup & Tuning

1. Initial parameter configuration, motor selection, and mode setup via driver panel or PC utility (e.g., Xinje Servo Tuner).

2. Use Inching (jog) and trial operations to manually test motor movement:

   • Set jog speed (P3‑18), toggle test/jog run, then press forward/reverse.ManualsLib

3. Adjust electronic gear ratio to match encoder counts to physical load turns.ManualsLib+1

4. Use monitor & auxiliary modes to observe real-time data like speed (e.g., U‑16) and status indicators.ManualsLib

C. Communication with PC

• Connect via RS‑232: use USB‑to‑DB9 adapter to link PC to servo driver.

• Open Xinje Servo Tuner (or download via Xinje website) and:

  • Select communication port

  • Choose “Auto Connect” or manually connect via COM settings to access drive info and tuning interface.PLCHMI Unlock

Gearbox / Reducer (20:1 Ratio) – Usage & Benefits

While not brand-specific, gear reducers (20:1 ratio) provide:

• Increased torque at output shaft

• Reduced speed—enabling precision and mechanical advantage

• Smoother motion control—especially important in low-speed, high-torque applications

• Installation requires solid mounting to align motor and reducer shafts, and some tuning adjustments (e.g., electronic gear ratio) to account for mechanical scaling.

Summary Table

For Your Website Content

• Landing Description: “The XINJE DS2‑21P5‑AS2 (1.5 kW) and DS5L‑21P5‑PTA (750 W) servo systems deliver precise, multi-mode motion control with advanced protection features. Options augmented with a 20:1 speed reducer to increase torque while maintaining tight control.”

• Usage Section: Include step-by-step wiring diagram, initial jogging, electronic gear ratio setup, and connection to PC via RS‑232.

• Features Highlights: Seamless mode-switching (position, speed, torque), high-resolution encoder, robust I/O, regenerative braking, built-in safety, compact LED interface, and precision tuning capability